Package Contents
Quoizel, Inc.
6 Corporate Parkway
Goose Creek, SC 29445
Customer Service
Phone 631.273.2700
Fax 631.231.7102
www.quoizel.com
ToolsRequired:Flathead screwdriver,Phillips screwdriver,pliers, wirecutters, wirestrippers, electricaltape,
safetyglasses.
BulbRecommended:
EstimatedAssemblyTime:
Preparation:
(3)Medium Base60W bulbsMaximum,Alternatebulb(3) 13WCFLMaximum.
20-30minutes
Identifyand inspectall partsbefore beginninginstallation. Checkpackage contentlist anddiagrams
belowto besure allparts arepresent. Ifany partsare missingor damaged,do notattempt toassemble, install,or
operatethe fixture.Contact customerservice forreplacement parts.
Warnings and Cautions
1of2
Assembly Instruction Sheet #IS-PCES1616C
For Style PCES1616C
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2014 QuoizelInc.
January2014
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
Hardware Contents
AA
EE
Crossbar
x1
Mounting Ball
x1
A
Ceiling Canopy
x1
BB
CC
DD
Lock Washer
x1
Hex Nut
x2
Nipple
x1
STEP 1 Install Crossbar-
A. AA)Attach the Crossbar ( to the Outlet Box with the head of the
Green Ground Screw facing you. Secure it with Outlet Box Screws
(not included) Tighten until snug..
Figure 1
Outlet Box
Outlet Box Screw
(not included)
AA
C
Lock Screw
x2
D
Flat Washer
x4
Green Ground Screw
STEP 2 Install Nipple to Crossbar-
* Pliers is required for this step.
A. Thread one Hex Nut (CC) to the middle of the Nipple (DD). Place the
Lock Washer (BB) over the Nipple (DD) and then thread the Nipple
(DD) into the Crossbar (AA) until the Nipple (DD) is about 0.375”
above the Crossbar (AA).
B
Shade
x1
B. Position the center hole of the Ceiling Canopy (A) over the end of
the Nipple (DD). Adjust the Nipple (DD) so approx 0.375” of the
Nipple (DD) is protruding from the mounting hole on the Ceiling
Canopy (A). This adjustment may take a few tries.
C. Remove the Ceiling Canopy (A) and then tighten the Hex Nut (CC)
against the Crossbar (AA) to secure in place.
D. Thread another Hex Nut (CC) onto the end of the Nipple (DD).
Thread this Hex Nut (CC) on just enough so the inside surface of the
Ceiling Canopy (A) rests against it. * You may have to trial fit the
Ceiling Canopy (A) one more times to insure this distance also. This
Hex Nut (CC) is needed here to prevent you from crushing down the
center of the Ceiling Canopy (A).
E. Refer to Step 3 for wire connections.
F. Attach the Ceiling Canopy (A) over the end of the Nipple (DD) and
secure with the Mounting Ball (EE). Hand tighten until snug.
AA
BB
CC
DD
CC
A
Step A
Step D
Figure 2
EE
STEP 3 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.) Strip and
prepare wire ends according to instructions supplied with
connectors.
B. Connect White Supply Wire from the Outlet Box to Ribbed side Wire
White wire
from supply
Ribbed side wire
from fixture
Black wire from
supply (or Red)
Smooth side wire
from fixture
Ground wire
from supply
Ground wire
from fixture
Figure 3
(2 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals